Up To 63A Current Simulation Evse Tester Series - PM701U/ PM701E/ PM701UT with Ifferent Mold Selection
Features of Up To 63A Current Simulation Evse Tester Series - PM701U/ PM701E/ PM701UT with Ifferent Mold Selection
- The adapter is capable of conducting electrical safety and functiontests on mode 3 electric vehicle charging equipment (EVSE) with a type2 connector .
- PE Pre-Test (potential presence of dangerous voltage at PE. terminalby mistake)-touch electrode and led lamp.phase indicator(presence of all three phase voltages measured to N)-
- three led lamps.PP state simulation (NC,13A,20A,32A,63A)-rotary switch.CP state simulation (A,B,C,D)-rotary switch.CP error “E" simulation (cp signal short-circuited to PE)-push button.PE error (earth fault)simulation (interruption of PE conductor)-pushbutton.
- Measurements on live conductors(L1,L2,L3 and N)and on PEconductor -five 4 mm safety sockets for connection to installationtesters.
- Test of cp signal-two 4mm safety sockets for connection to anoscilloscope.
- Mains socket (on backside) to connect an external load only for testpurposes.
| Mode | PM701U | PM701E | PM701UT |
| Test Object | AC charging station | AC charging station | AC charging station |
| Test Interface | Complies with SAE J1772 stangard | Type2(European Standard) | NACS(Tesla) |
| Simulate chargeing state | A,B,C or D | A,B,C或D | A,B,C或D |
| PE pre testing | √ | √ | √ |
| CP pre testing | √ | √ | √ |
| Simulate cable resistance | √ | √ | √ |
| Simulated CP error | √ | √ | √ |
| Simulated PE error | √ | √ | √ |
| Leakage tripping test | ≥6mA/110V | | ≥6mA/110V |
| Charging output terminal | 4mm port/American standard socket | 4mm port/European standard socket | 4mm port/American standard socket |
| Support voltage types | Single phase or three-phase | Single phase or three-phase | Single phase or three-phase |
| Indicator light | √ | √ | √ |
| Fuse | 10A/250V | 10A/250V | 10A/250V |
| General |
| Protection grade | Case IP54 |
| Safety Rating | IEC/EN 61010-1,IEC/EN61010-2-030,CAT Ⅲ 600V |
| Measurement Category | IEC/EN 61851-1,IEC/HD 60364-7-722 |
Product Description of Up To 63A Current Simulation Evse Tester with Ifferent Mold Selection
The adapter is capable of conducting electrical safety and functiontests on mode 3 electric vehicle charging equipment (EVSE) with a type2 connector .
- 1-simulate connection of an electrical vehicle to the testedcharging station (the test adapter simulates electrical vehicle andcharging cable),connection of the test adapter to a chargingstation triggers the charging process in the charging station (CPswitch at the adapter shall be in appropriate mode), various cablecharging capabilities can be simulated(NC,13A,20A,32Aand63A)as well as all possible electrical vehicle modes(A,B,C,D).2-To provide convenient access to charging terminalsL1,L2,L3,N,PE and to CP signal terminals to which additionalmeasuring equipment can be connected for further testing,charging stations should be tested after installation and repeatedperiodically.
- Visual inspectionContinuity of protective conductors and protective bondi!
- Insulation resistances
- Loop/Line impedance.RCD testFunction tests (including but not limited to):
- Vehicle state A,B,C,D-Error handing (error “E",PE Error (Earth Fault)...)
- Communication (PwM signal)
- Mechanical locking of plug-
- Rotary field/phase sequence
- Other tests
Service
- All products have 12 months warranty, maintenance will not charge during this period (excluded damage of error operation, damage of battery or surface), and delivery fee will be borne by the customer.
- Material and service fee will be charged when warranty is expired, and delivery fee will be charged.
- To product which is out of warranty but has already repaired, we will provide another three months free service if the same spare part has problem recurs.
- Customer can refer the maintenance order to get more information.
Detailed Images of Up To 63A Current Simulation Evse Tester with Ifferent Mold Selection
Our Target
We aim to produce intelligent instruments, provide high quality services, and become an innovative manufacturer.
R&D Team
Our R&D team have over 20 years R&D experience in instrument industry .
Mission
Our mission is to get our work done well to become customer’s reliable business friend. S.E.Q( Service , Economic pricing , Quality ) is our concern , we know what you need ,and we know what we have .
